Electronic Energy Source
"Demand The Best - Demand E.E.S."
I like cats, they taste just like chicken... I like chicken, they taste just like cats ! !
For Best View Security Set On Low
This Site Is Under Construction, Revisions, & Updates 24/7/365
E.E.S. Disclaimer Please Read.
There will be a lot of changes made to the site for a few days, so there might be things go outta whack. Please bare with us.
This website is composed of
When in doubt: imagine.
He who dies with the
There is no danger of developing eyestrain
The two best physicians of them all are
Give a man a fish and he will eat.
Friends: People who know you well, but like you anyway. And even visit you when you are broke.
"Freedom isn't free."
There are 10 kinds
of people in this world. Those that understand binary,
Pantech Breeze III Owners with AT&T Unlimited Data Plan:
Get the most out of your Breeze III by using it to connect your PC to it as the Controller!
Unlimited BANDWIDTH and speeds up to 921.6kbps (Windows XP) is right there in the phone. Download full length movies, music videos, programs; and the works... You never have to worry about how much data you use if you follow instructions provided in E.E.S.'s - "It's A Breeze" for maximizing your Pantech Breeze III with AT&T.
This little cell phone is better than an Android type device once it it fully energized... AT&T does not tell you the full story about the capabilities of this phone... They will tell you that the phone is incapable of doing what E.E.S. has discovered by "UNLOCKING" just one path within the cell.... And it is completely LEGAL.
"It's A Breeze" by E.E.S. Provides all the Instructions & Program to accomplish this. The data is delivered to you via eMail. Easy to follow instructions and program !
Oscilloscope Probe For Detection Of Bad Parts
The Oscilloscope Probe made by Electronic Energy Source is an inexpensive addition to a scope. You’d be surprised as to what you can do with your scope having the right probes.
The requirements of your scope; it must be able to run in X-Y mode. It will not matter as to the number of channels it can display at a time. Just an independent Horizontal and Vertical input in X-Y mode/function.
Timing does not matter in X-Y mode with this device.
The Probe has BNC connectors for the input X & Y for your scope. Most multi-channel scopes are marked Chan 1 as "X" and Chan 2 as "Y"
It has a 1/8th inch standard mono plug on the wall power transformer to power the probe's circuitry.
The Red and Black long leads allow you to reach parts testing at about 3-feet from the probe.
.Once you play around with this probe, you will learn quickly which components you can test while
they are still in a circuit. This is exceptionally good for testing RF transistor while still screwed
down to the heat-sink by only lifting two of the four contacts upward from making contact with the circuit.
I have never tried to write an instruction manual for this device, as each person, will learn their needs in
time and their own ways to use it.. The key to being good with this thing is you have to observe and pay attention to the patterns.Pay attention to details.
Some simple patters this probe makes on the scope's screen can be seen in the Scope Probe Screens drawing which is displayed in the accompanying photos.
A new part, tested from a certain pin to a certain pin with a certain polarity will show a defined pattern. If you look at an unknown good or suspected bad part, testing it exactly as you did with the known good new part, should you find ANY differences in what pattern you should be seeing, then there is something wrong with that part.! !
What’s wrong?? Who cares… we throw that part away.
time permits, I will increase data in reference to the device’s use and some
how to’s… If you buy one of these probes, check for updates on its operation
often by returning to the enlisted page for the probe.
was introduced to this type probe in 1967 while I was going to an electronics
school at Fort Monmouth, NJ
Station Electronic Equipment Repair).
later found that Popular Electronics ran it in their “Think Tank Projects”
was a one hour block on introduction to the oscilloscope.
When they showed it to the class it was described in it’s simplicity
and stated how helpful it is in locating flaws in just about anything that uses
electricity if you know what the GOOD part is supposed to look like; [point to
that time, I have almost always had one of these probes available to my work
bench o’scope. When I retired
from the Army in 1984; I set up a small CB shop in
will now start instructions of one of it simplest uses;
A “Final” in a CB radio without removing it from the radio in done by
unsoldering each of the outside pins from the main board and leave the center
pin connected. This frees the
transistor so you have direct undisturbed measuring access.
WILL BE ADDED AS TIME PERMITS !
If you work on linears, it is especially valuable for testing finals without the time and effort of removing them.
Send mail to
Webmaster with questions or
comments about this web site.